Function
機能
- Use this function to enter the allowable stress coefficients. Often, the user may wish to define the allowable stresses rather than using the values calculated according to the applied design code during the strength verification of steel members. The coefficient values entered are ratios to the yield strength (Fy) of the relevant steel material.
- この関数を使用して、許容応力係数を入力します。 多くの場合、ユーザーは鋼材部材の強度検証中に適用された設計コードに従って計算された値を使用するよりも、許容応力を定義したい場合があります。 入力された係数値は、当該鋼材の降伏強度(Fy)に対する割合です。
Call
呼び出し
From main menu, select [Design] tab > [Type : Steel Design] > [Design Input Data] group > [Design Parameters] > [Specify Allowable Stress]
メインメニューから[Design]タブ>[Type : Steel Design]>[Design Input Data]グループ>[Design Parameters] > [Specify Allowable Stress]
Input
入力
First, select the members in the model and enter the following :
最初にモデルからメンバーを選択し、次を入力します:
Option
Select Add/Replace or Delete.
Add/Replace : Add the newly entered values or replace the previously entered values.
Delete : Delete the entered values. Data entry is not required when deleting.
Option
Add/ReplaceまたはDeleteを選択します。
Add/Replace : 新しく入力した値を追加するか、以前に入力した値を切り替えます。
Delete : 入力した値を削除します。 削除時にデータ入力は必要ありません。
Define Allowable Stresses
Enter the allowable stress coefficients (refer to (1)).
Axial Compression (Fa) : Allowable compression stress coefficient for the compressive force along the member's axial direction (refer to (2))
Axial Tension (Ft) : Allowable tension stress coefficient for the tensile force along the member's axial direction (refer to (3))
Major Bending (Fby) : Allowable bending stress coefficient for the bending moment about the member's strong axis (refer to (4))
Minor Bending (Fbz) : Allowable bending stress coefficient for the bending moment about the member's weak axis (refer to (5))
Shear (Fv) : Allowable shear stress coefficient for the shear force (refer to Note 5)
: Apply the entered values to the selected members.
: Close the entry Dialog Bar.
Define Allowable Stresses
許容応力係数を入力します (参照 (1)).
Axial Compression (Fa) : 部材の軸方向による圧縮力に対する許容圧縮応力係数 (参照 (2))
Axial Tension (Ft) : 部材の軸方向による引張力に対する許容張力応力係数 (参照 (3))
Major Bending (Fby) : 部材の鋼軸に対する曲げモーメント許容応力係数 (参照 (4))
Minor Bending (Fbz) : 部材の略軸に対するバンディングモーメントの許容バンディング応力係数 (5))
Shear (Fv) : せん断力に対する許容せん断応力係数 (注5参照)
: 入力した値を選択したメンバーに適用します。
: アイテム ダイアログ ボックスを閉じます。
(1)
This can be applied only for the AISC-ASD89 and AIK-ASD83 design codes. This is not applicable for the strength verification of steel-RC composite column members.
(2)
Fa stands for the allowable compressive stress for the compressive force in the member's axial direction.
(3)
Ft stands for the allowable tensile stress for the tensile force in the member's axial direction.
(4)
Fby and Fbz represent the allowable bending stresses for the bending moments about the member's strong and weak axes respectively. Same values are applied to all the bending stresses for the tension and compression fibers irrespective of the signs of the bending moments.
(5)
Fv stands for the allowable shear stress for the shear forces in the strong and weak-directions. The same value applies to both strong and weak-directions.
(6)
When the values of the allowable stress coefficients are repeatedly entered for the same members, the values will be updated to the last values entered.
(7)
The entered values for the allowable stress coefficients can be reviewed in the data table arranged in the order of element numbers. The user may Modify/Add and Delete items in the data table.
Access the data table following the procedure below.
From the Main Menu select Design > Steel Design Parameter > Steel Design Tables > Specify Allowable Stresses.
From the Tables tab of the Tree Menu select Design Tables > Steel Design Table > Specify Allowable Stresses.
(1)
これはAISC-ASD89およびAIK-ASD83設計コードにのみ適用可能であり、鋼-RC複合柱部材の強度検証には適用されません。
(2)
Faは部材の軸方向圧縮力に対する許容圧縮応力を示します。
(3)
Ftは部材の軸方向引張力に対する許容引張応力を意味します。
(4)
FbyとFbzはそれぞれ部材の強い軸と弱い軸に対する曲げモーメントに対する許容曲げ応力を示します。 曲げモーメントの符号に関係なく、張力と圧縮繊維に対するすべての曲げ応力には同じ値が適用されます。
(5)
Fvは強い方向と弱い方向のせん断力に対する許容せん断応力を示します。 強い方向と弱い方向の両方に同じ値が適用されます。
(6)
許容応力係数の値が同じ部材に対して繰り返し入力されると、値が最後に入力された値に更新されます。
(7)
入力された許容応力係数の値は、元素番号順にリストされたデータテーブルで確認できます。 ユーザーは、データ テーブル内のアイテムを修正/追加および削除できます。
以下の手順に従って、データ テーブルにアクセスします。
Main Menuから Design > Steel Design Parameter > Steel Design Tables > Specify Optable Stressを選択します。
Tree Menu의 Tables タブで Design Tables > Steel Design Table > Specify Optable Stressを選択します。